The correct oil filter for a 2007 Toyota Camry is the Toyota part number 90915-YZZA1, a spin-on filter that costs between $8 and $15 at most auto parts stores
The 90915-YZZA1 fits all 2007 Camry models regardless of engine size — the four-cylinder and V6 versions use the same filter. You can find it at Toyota dealerships, AutoZone, O'Reilly Auto Parts, Advance Auto Parts, and Walmart, usually in stock. If you cannot locate that exact part number, ask the parts counter for "2007 Camry oil filter" and they will pull the right one from their system.
The filter threads onto the engine block on the driver's side, below the intake manifold. You do not need any special tools beyond a filter wrench (a $5 to $10 tool that grips the filter canister) and a drain pan. The whole job takes 15 to 20 minutes if you are changing the oil at the same time, which most people do.
Key Takeaways
- The Toyota part number 90915-YZZA1 is the original filter for all 2007 Camry engines and costs $8 to $15.
- The filter location is on the driver's side of the engine, below the intake manifold, and requires only a filter wrench to remove.
- You can buy this filter at any major auto parts retailer, Toyota dealerships, and many general retailers without ordering ahead.
- When installing a new filter, hand-tighten it until the rubber gasket touches the engine block, then turn it three-quarters of a turn more — do not use a wrench to tighten.
Where to buy the 90915-YZZA1 filter
Most auto parts stores stock this filter because the 2007 Camry is still common on the road. Call ahead or check the store's website to confirm they have it in stock before you drive over. The filter usually sits on a shelf near the oil section, organized by vehicle year and make.
Toyota dealerships carry the genuine part and will have it in stock the same day. Dealership prices run $12 to $18, slightly higher than independent retailers. If you want to be certain you have the exact original part, the dealership is the safest choice, though not necessary — the 90915-YZZA1 is a common filter and any retailer that stocks it will have the genuine Toyota version.
Online retailers like Amazon ship the filter to your home, but you will wait one to three days. If you are changing the oil today, buy in person. If you are planning ahead, online ordering saves a trip and sometimes costs less.
How to locate the filter on your engine
Open the hood and look toward the driver's side of the engine. The filter is a cylindrical canister about 3 inches tall and 2.5 inches wide, with a threaded base. On the 2007 Camry, it sits directly below the intake manifold (the large plastic piece that runs across the top of the engine). You will see it when ready once you know where to look.
If you cannot spot it, trace the oil pressure line from the top of the engine down toward the block — the filter is where that line connects. The filter will have a small amount of oil residue around its base, which is normal. Place your drain pan underneath before you touch it, because oil will spill when you unscrew it.
Removing the old filter
Slide your drain pan under the filter. Use a filter wrench to grip the canister near its base — the wrench looks like a metal band with a handle, and it costs $5 to $10 at any auto parts store. Turn the wrench counterclockwise to loosen the filter. Once it is loose enough to turn by hand, unscrew it the rest of the way by hand, turning slowly so oil does not splash out.
The old filter will contain about half a quart of oil, so expect some spillage. Let it drain into the pan for 30 seconds before setting the filter aside. Wipe the threaded base on the engine block with a clean rag to remove any old gasket material or debris. This step prevents the new filter from sealing incorrectly.
Installing the new filter
Take the new 90915-YZZA1 filter out of the box. Before you install it, pour a small amount of new oil (the same grade you are using for the oil change) into the filter canister through the open end. Fill it about three-quarters full. This pre-fills the filter so the engine does not run dry for the first few seconds after you start it.
explore a thin layer of new oil to the rubber gasket (the flat ring around the threaded base of the filter). This helps the gasket seal properly and makes removal easier next time. Screw the filter onto the threaded base by hand, turning clockwise. When the rubber gasket first touches the engine block, you will feel a slight resistance. At that point, turn the filter an additional three-quarters of a turn — no more, no less.
Do not use a wrench to tighten the filter. Hand-tightening is correct. Over-tightening damages the gasket and makes the filter difficult to remove at the next oil change. Once it is installed, start the engine and let it run for 30 seconds, then turn it off and wait two minutes. Check underneath the filter for leaks. If oil is dripping, the filter is not sealed correctly — turn it another quarter turn and check again.
Aftermarket filters that fit your 2007 Camry
If you cannot find the Toyota 90915-YZZA1 or prefer an aftermarket option, several brands make filters that fit the 2007 Camry. Fram PH8A, Mobil 1 M1-110, and Bosch 3323 all work in this vehicle. These filters cost $6 to $12 and perform the same function as the Toyota original. The installation process is identical — they all use the same threaded base and gasket design.
Aftermarket filters are not inferior to the Toyota original. They meet the same industry standards and filter the oil just as effectively. The main difference is price and availability. If an aftermarket filter is in stock and the Toyota part is not, either one will work. Check the box to confirm the part number matches your vehicle year before you buy.
How often to change your Camry's oil filter
Toyota recommends changing the oil filter every time you change the engine oil. For a 2007 Camry, that is every 5,000 miles if you drive in normal conditions, or every 3,000 miles if you drive in severe conditions (frequent short trips, towing, dusty environments, or extreme temperatures). Check your owner's manual for the specific interval that applies to your driving.
The filter should never be reused. Once it is removed, discard it in the trash or take it to an auto parts store — many retailers accept used filters for recycling at no charge. Never pour the old filter's oil down a drain; dispose of it according to your local hazardous waste guidelines, usually by taking it to a service station or recycling center.
Frequently Asked Questions
Can I use a different filter size if I cannot find the 90915-YZZA1?
No. The filter size and thread type must match exactly, or it will not seal properly and oil will leak. If your local store does not have the 90915-YZZA1 in stock, order it online or call another store location. Do not substitute a different part number.
What if oil leaks from the filter after I install it?
The gasket is not sealed. Turn off the engine, let it cool for five minutes, and tighten the filter another quarter turn by hand. Start the engine again and check for leaks. If it still leaks, remove the filter, wipe the threaded base clean, and install a new filter, making sure to oil the gasket first.
Do I need to drain the oil before changing the filter?
No, but most people change both at the same time because you have the drain pan out anyway. If you are only changing the filter, you can do that alone — the oil stays in the engine. However, the filter traps contaminants, so changing it without changing the oil means the new filter is working in dirty oil.
How tight should the filter be when I install it?
Hand-tight plus three-quarters of a turn. You should be able to turn it by hand without a wrench. If you need a wrench to turn it, it is too tight. The gasket will seal correctly at hand-tight, and over-tightening damages it.
Can I recycle my old oil filter?
Yes. Most auto parts stores accept used filters for recycling at no charge. Some recycling centers also take them. Never throw an oil filter in the trash — the oil inside is hazardous waste. Drain as much oil as possible from the old filter into your drain pan before you take it in for recycling.