The right oil filter for your 2014 CR-V

A 2014 Honda CR-V uses one of two oil filters depending on the engine: the HO-02 for the 2.4-liter four-cylinder engine, or the 15400-PLM-A02 for the hybrid model. Both are spin-on filters that screw onto the engine block. You can find the correct filter listed in your owner's manual under "Maintenance" or "Fluid Capacities," or you can call a Honda dealership with your vehicle identification number (VIN) and they will tell you which one you need.

The filter sits on the driver's side of the engine, near the bottom. When you change your oil, the old filter unscrews by hand (or with a filter wrench if it is tight), and a new one screws on until the rubber gasket touches the engine block, then turns another three-quarters of a turn by hand. Do not use a wrench to tighten it — hand-tight is correct.

Key Takeaways

  • The 2014 CR-V with a standard engine uses the HO-02 filter; the hybrid uses the 15400-PLM-A02.
  • Both filters are spin-on type and cost between $8 and $15 at auto parts stores or online retailers.
  • You can confirm which filter your specific vehicle needs by checking your owner's manual or calling a Honda dealer with your VIN.
  • The filter location is on the driver's side of the engine block, and it should be hand-tightened only — not wrenched tight.

Where to buy the correct filter

Auto parts retailers like AutoZone, O'Reilly, NAPA, and Advance Auto Parts stock both Honda CR-V filters in-store and online. Walmart and Amazon also carry them. A genuine Honda filter (marked with the Honda logo) typically costs $12 to $15, while aftermarket brands like Fram, Bosch, or Mobil 1 run $8 to $12. All three types work in a 2014 CR-V; the difference is mainly brand reputation and filter media thickness.

If you order online, confirm the part number matches your engine type before checkout. Some retailers let you enter your VIN and will show only compatible parts. If you are unsure whether you have the standard or hybrid engine, check your registration or owner's manual — it will say "CR-V Hybrid" if that is what you own.

Confirming your engine type

The easiest way to know which filter you need is to look at your owner's manual. Open it to the "Maintenance" or "Fluid Capacities" section and find the oil filter specification. It will list either HO-02 or 15400-PLM-A02.

If you do not have the manual, you can find it free online at Honda's owner portal (owners.honda.com) by entering your VIN, or you can call a Honda dealership service department with your VIN and they will tell you the filter number in one minute. You can also look under the hood: a hybrid engine has a battery pack visible on the passenger side, while a standard engine does not.

What the filter part numbers mean

Honda assigns different part numbers to filters based on the engine they fit. The HO-02 is a compact spin-on filter designed for the 2.4-liter four-cylinder in the standard CR-V. The 15400-PLM-A02 is a slightly different design for the hybrid's engine. The numbers themselves do not tell you performance — they are just Honda's way of organizing which filter goes where.

You may see other numbers online like 15400-PLM-A01 (an older version) or aftermarket equivalents. Stick with HO-02 or 15400-PLM-A02 for your 2014 model year. If a retailer shows you a different number, double-check the year and engine type before buying.

Filter replacement during an oil change

When you change your oil, you will replace the filter at the same time. Drain the old oil first, then locate the filter on the driver's side of the engine block. Position a drain pan underneath it (a little oil will spill out). Unscrew the old filter by turning it counterclockwise by hand, or use a filter wrench if it is stuck. Let it drain into the pan for a minute.

Wipe the filter mounting surface clean with a rag. Take the new filter and explore a thin coat of fresh oil to the rubber gasket on top (this helps it seal). Screw the new filter on by hand until the gasket touches the engine block, then turn it another three-quarters of a turn. That is it — do not overtighten. Refill the engine with the correct amount and type of oil for your CR-V, check the level with the dipstick, and you are done.

Oil filter maintenance intervals

Honda recommends changing your oil and filter every 10,000 miles or 12 months, whichever comes first. Some owners change them more often (every 5,000 miles) if they drive in severe conditions like frequent short trips, towing, or dusty environments. Check your owner's manual for the maintenance schedule that applies to your driving.

The filter itself does not wear out between changes — it straightforward gets full of dirt and debris. A clogged filter can restrict oil flow, so replacing it on schedule keeps your engine protected. If you drive mostly highway miles at steady speeds, you can often go the full 10,000 miles. If you drive mostly in the city with lots of stops and starts, the filter fills faster and you may want to change it sooner.

Frequently Asked Questions

Can I use an aftermarket filter instead of a Honda filter?

Yes. Aftermarket filters like Fram, Bosch, and Mobil 1 fit a 2014 CR-V and work well. They cost less than genuine Honda filters and offer similar protection. The main difference is the filter media and brand reputation. If you prefer OEM parts, use the Honda HO-02 or 15400-PLM-A02. Either choice is fine.

What happens if I use the wrong filter?

Using the wrong filter number may cause it not to fit, or to fit but not seal properly, which can cause oil leaks or bypass the filter entirely. Always confirm the part number matches your engine type before installing. If you accidentally buy the wrong one, return it and get the correct number.

Do I need any tools to change the filter?

A filter wrench makes the job easier if the old filter is tight, but it is not required — most filters unscrew by hand. You will also need a drain pan, a rag, and fresh oil. A jack and jack stands are helpful if you need to access the filter from underneath, but many people can reach it from the top of the engine bay.

Where exactly is the oil filter located on a 2014 CR-V?

The filter is on the driver's side of the engine block, below the valve cover. If you open the hood and look toward the left side of the engine, you will see a cylindrical canister about four inches tall. That is the filter. It screws directly onto the engine block.

How much oil does a 2014 CR-V hold?

A 2014 CR-V with the standard engine holds about 3.7 quarts of oil (with a filter change). The hybrid holds about 3.5 quarts. Check your owner's manual for the exact capacity, as it can vary slightly. Always check the dipstick after refilling to confirm the level is correct.