What the Lippert Auto Level reset does

The Lippert Auto Level is a leveling system found on many RVs and travel trailers that automatically adjusts hydraulic jacks to keep your vehicle level when parked. A reset clears the system's memory and recalibrates the sensors so the leveling function works correctly again. You perform a reset when the system stops responding, gives false readings, or fails to level your RV properly.

The reset process differs slightly depending on which Lippert control panel you have — the most common are the older mechanical models and the newer digital touchscreen versions. Both resets take less than five minutes and require no tools or special equipment.

Key Takeaways

  • A Lippert Auto Level reset clears the system memory and recalibrates the sensors when leveling stops working correctly.
  • The reset method depends on your control panel type: mechanical switches use a power cycle, while digital panels have a dedicated reset button or menu option.
  • You must turn off the main power switch and wait at least 30 seconds before turning it back on for a mechanical system reset.
  • After resetting, the system will recalibrate on its own the next time you use it, which takes a few seconds.
  • If the system still fails after a reset, the problem is likely a sensor or hydraulic issue that requires professional service.

Resetting a mechanical Lippert control panel

Mechanical panels have a large power switch and separate buttons for each jack. To reset this type, locate the main power switch on your control panel — it is usually labeled "Power" or "Main" and sits at the top or side of the panel. Turn the switch to the Off position.

Wait at least 30 seconds with the power off. This allows the system's internal capacitors to fully discharge and clears any stuck data from the memory. After 30 seconds, turn the power switch back to On. You should hear a brief beep or see a light flash, which signals the system has restarted. The reset is complete.

Test the system by pressing one of the leveling buttons. The jacks should respond normally. If they do not, wait another minute and try again — sometimes the system needs a moment to fully reinitialize after power returns.

Resetting a digital Lippert touchscreen panel

Digital panels display a menu on a small screen and have touch buttons or a physical reset button. The fastest method is to look for a Reset or System Reset button on the panel itself — some models have this as a recessed button you press with a pen or small tool. Press and hold it for three to five seconds until the screen goes blank or shows a confirmation message.

If there is no physical reset button, use the touchscreen menu. Press Menu or Settings, then look for an option labeled Reset, Recalibrate, or System Reset. Select it and confirm when the panel asks you to verify. The screen will go dark briefly, then return to normal operation.

Some newer digital models also allow you to reset by turning off the main power switch and waiting 30 seconds, just like mechanical panels. Check your owner's manual to see which method your specific model supports.

What happens after you reset

Once the reset is complete, the system will recalibrate itself the next time you use the leveling function. This means the first time you press a leveling button after the reset, the jacks may move slightly or pause for a few seconds while the sensors relearn the vehicle's position. This is normal and expected.

Do not interrupt this first leveling cycle — let the jacks run through their full motion without pressing any buttons. After this initial cycle, the system should respond normally to all future commands. If the jacks still do not level correctly or move erratically, the problem is not a straightforward reset issue.

When a reset will not fix the problem

A reset works only if the problem is a software glitch or temporary sensor confusion. If your system still fails after a reset, the issue is likely a faulty sensor, a hydraulic leak, a broken jack motor, or a wiring problem. These require professional diagnosis and repair.

Signs that you need professional service include: jacks that move but do not stop at the right height, jacks that move on only one side of the RV, a control panel that does not power on at all, or hydraulic fluid leaking from the jack cylinders. Contact an RV service center or Lippert directly for these issues — they cannot be fixed with a reset.

Finding your control panel type and manual

If you are unsure whether your panel is mechanical or digital, look at it directly. Mechanical panels have large physical buttons and a straightforward on-off switch with no screen. Digital panels have a small LCD or touchscreen display and touch-sensitive buttons or a menu system.

Your RV's owner's manual will have the exact reset steps for your specific model and panel version. If you do not have the manual, search online for "Lippert Auto Level [your model number] manual" — the model number is usually printed on the panel itself or on a sticker inside your RV's electrical compartment. Lippert also publishes reset instructions on their website organized by product line.

Frequently Asked Questions

Will resetting my Lippert system erase any stored settings?

A reset clears the system memory and recalibration data, but it does not erase personal settings like preferred leveling speed or jack pressure if your model has those options. After the reset, the system will recalibrate on its own the next time you use it. Check your manual to see if your specific model stores any user preferences that might be affected.

How often should I reset my Lippert Auto Level?

You should only reset when the system stops working correctly — not as routine maintenance. A normal system does not need regular resets. If you find yourself resetting more than once every few months, the underlying problem is likely a failing sensor or hydraulic issue that needs professional attention.

Can I reset my Lippert system while the RV is parked on uneven ground?

Yes, you can reset the system anywhere. The reset itself does not depend on the RV being level. However, after the reset, do not use the leveling function until the RV is parked in its final position, because the system will recalibrate based on wherever it is when you first use it after the reset.

What if my control panel has no power after I try to reset it?

Check that the main battery disconnect switch on your RV is in the On position — the Lippert system draws power from your RV's house battery. Also verify that the breaker or fuse for the leveling system has not tripped. If power still does not return, the problem is electrical and requires professional service.

Does a reset fix jacks that move slowly or make noise?

A reset will not fix mechanical problems like slow jacks or grinding sounds. These indicate a hydraulic or motor issue. A reset only fixes software glitches where the system stops responding or gives incorrect readings. If your jacks move but sound wrong or move too slowly, have the hydraulic system inspected by an RV technician.